FAQ

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

During screw conveyor operation, internal breaker is blocked due to overload.

After removing the cause of the error of the breaker (QM67) setting value or more overcurrent, check the operation status.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

During bed flushing, the internal breaker is blocked due to overload.

After removing the cause of the error of the breaker (QM18) setting value or more overcurrent, check the operation status.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

When the coolant gun is operating, the internal breaker is blocked due to overload.

After removing the cause of the error of the breaker (QM16) setting value or more overcurrent, check the operation status.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

In case of oil skimmer operation, internal breaker is blocked due to overload.

After removing the cause of the error of the breaker (QM51) setting value or more overcurrent, check the operation status.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

During jet coolant operation, the internal breaker is blocked due to overload.

After removing the cause of the error of the breaker (QM17) setting value or more overcurrent, check the operation status.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

When external hydraulic system is operated, internal breaker is blocked due to overload.

After removing the cause of the error of the breaker (QM-) setting value or more overcurrent, check the operation status.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Insufficient manual tool change conditions.

Check the position of each axis where tool change is possible. Check whether a large diameter tool is installed. If there is an ATC door, check that it is open.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Cycle start and coolant operation are performed while the door is not closed.

Make sure the door is closed. Check the door closing signal and check the LED on the control panel button. Occurs even when rotating the spindle in release mode.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

In the origin return mode, the Z axis is not the origin.

Alarm is automatically released after Z axis completes homing.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Machine Lock, Z Axis Lock, and automatic home return function for all axes are used when automatic operation is not terminated.

Machine Lock, Z axis Lock: Run after releasing the function. Automatic operation: after reset, run.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Manual tool change that does not meet the conditions is executed.

1. Check the operation of the magazine. 2. Check the position of the shaft for tool change. 3. Check the exact position of the ATC Arm 4. Check the spindle clamp. 5. Pneumatic and hydraulic check

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Tool change performed when the ATC Arm is not in the correct position.

After moving the ATC Arm to the correct position, run again.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Tool change performed while the spindle is not clamped.

After clamping the spindle, run again.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Tool call without the magazine door closed. Magazine door is open during magazine operation.

Check that the magazine door is closed. Check the magazine door close signal.

PMC Rank I Alarm

Only the device is limited in motion and there is no obstacle to axis traversing.

Calls up the tool mounted on the spindle.

Check tool number.